Eltek Rectiverter Integrated Standalone System 3kVA 1phase 220 VDC
(Part No.:CTOR0201.003 CTOR0201.006 )
Applications :
The rectiverter integrated standalone system can be used in
application where
1 230/115Vac backup is needed in parallel with the 220Vdc backup .
The system can be integrated into an Eltek DC system and connected
to the same controller as the 220Vdc systems
It can also be used as a standalone system connected to any
available, 220Vdc source.
The total output power for both AC and DC output is limited to max
4kw, AC and DC output limits can be set according to the attached
load.Where the limitation for AC load is set to max 3Kva.
TELECOM-MOBILE/WIRELESS
l LTE/4G/WiMAX
l Distributed antenna system
l Broadband
l Radio base stations/cell sites
l ·
l RAILWAY & METRO INFRASTRUCTURE
l Control & protection
l Signaling
l GSM-R
l Safety Systems
l ·
l POWER UTILITIES
l Control & protection
l SCADA system
Key Features :
Compact design and simple installation
Single phase 230 or 115VAC input and output
l 48Vdc input and output
l Up to 4 rectiverter modules
l 8KW total AC+DC output
l Max 6kVA AC output
l Max 4KW/ 8KW DC output
l 1 or 2 pole AC distribution options
l 1 Pole DC distribution option
l Built in transfer technology
Techinical Data:
|
| Models / ordering information | | 4 kW, 230 V | 2 kW, 115 V |
| Part number | | CTOR0201.003 | CTOR0201.006 |
| AC OUTPUT DATA |
| Voltage (default) / (adjustable range)1) | 230 VAC / 200 - 240 VAC | 115 VAC / 100 - 127 VAC |
| Frequency (default inverter mode) | | 50 Hz (adaptive) | 60 Hz (adaptive) |
| Frequency (set-able inverter mode) | | 50Hz, 60Hz or last synced 50/60Hz (adaptive) |
| Power maximum (continuous / overload (<15s) ) | 2400 W (3000 VA) / 4000 VA | 1200 W (1500VA) / 2000 VA |
| Current maximum (continuous / overload (<15s) ) | | 13ARMS / 17,4ARMS |
| Current (maximum) Quick trip (20ms) | | 64 A (6 x nominal) |
| Hold up (Voltage dips) (before switching to battery) | | 5 ms |
| THD | | < 1.5 % at resistive load |
| Output features | | Fuse in L and N, Hot pluggable |
| DC OUTPUT DATA |
| Voltage (default) / (adjustable range) | | 245 VDC / 194 - 290 VDC |
| Power (maximum @nominal input) | | 2400 W 2) | 1200 W 2) |
| Current (maximum @nominal output VDC) | | 11,1 A 2) | 5,5 A 2) |
| Hold up time, maximum output power | | >10ms; VOUT > 95 VDC |
| Output features | Short circuit proof, Over voltage Shutdown, Bulk DC output
connection to M6 bolt |
| INPUT DATA |
| AC Mains Input Voltage (single phase) | | 185 - 275 VAC | 95 - 140 VAC |
| AC Current (at nominal output voltage) (depending on module type) | 14-24 ARMS 4) |
| Frequency (default: sync range) | | 47-53 & 57-63 Hz | 57-63 & 47-53 Hz |
| Frequency (set-able: sync range) | | 47-53 Hz, 57-63 Hz or both (adaptive) |
| Power Factor / THD | | > 0.99 at 50% load or more / < 3.5% |
| DC Voltage nominal / extended range (no overload)3) | | 204 - 290 VDC / 180 - 204 VDC |
| DC Current (maximum) | 13,3 A / 18 A during overload (15s) | 6,4 A / 9 A during overload (15s) |
Input features | | Fuse in L and N, Hot pluggable, Varistor, Hot pluggable AC input individual screw terminals 6 mm2 for L, N & PE Bulk DC
input connection to M6 bolt |
| OTHER SPECIFICATION |
| Support for connection to following controller (RJ45) | Smartpack2, Smartpack S & Compack controllers |
| Efficiency | >96% (mains mode (AC/AC and AC/DC)), >94% (inverter mode
(DC/AC)) |
| 2 pole AC distribution (connection IEC 320-C13 sockets) | 3pc, 10A, OP characteristics (optional 4-8 A breaker with CS
characteristics available) |
| Protection Class | IP 20 | | |
| Operating temperature | -40 to +55°C (+40 to +131°F), humidity 5 - 95% RH non-condensing |
| Storage temperature | -40 to +85°C (-40 to +185°F), humidity 0 - 99% RH non-condensing |
| Dimensions[WxDxH] / Weight | 482 x 395 x 44mm (1U) (19 x 17 x 1,8”) / 6kg (13 lbs) |
| DESIGN STANDARDS |
| Electrical safety | EN 60950-1, EN 62040-1 | |
| EMC | ETSI EN 300 386 V.1.6.1, FCC CFR 47 Part 15 EN 61000-6-1/-2/-4/-5 EN62040-2 (Cat C1 emmisions, cat C2/C3 immunity) |
Environment | ETSI EN 300 019: 2-1 (Class 1.2) & 2-2 (Class 2.3) Normal operating conditions as per IEC/EN 62040-3:2011 clause 4.2. Other operating conditions as per IEC 62040-3:2011 clause 4.3, must
be advised 2011/65/EU (RoHS) & 2012/19/EU (WEEE) |
1) Output voltage ranges configured in factory and have individual
keying in top chassis 3) Reduced performance - no power boost and increased voltage THD
on AC output. | 2) AC load has priority. Maximum available DC output power and current is dependent on instant AC load and AC input voltage; i.e maximum 1600W at full AC power and
nominal input for 230VAC. 4) If DC voltage is pulled below 194 V the input current may
increase above this level |
Related Products:
Solutions
We provide a complete solutions including site survey, propose
professional plan according to customer’s request ,technical
support, and maintenance service for Telecommunication Companies in
and out of China. We have a competent team and a network of trusted
Partners around the world.
FAQ :
1. How do you control the quality?
A:All products before the shipment are simulated usage scenarios,
load and full load and current sharing test to ensure the quality
of the product.
2. What is your minimum order quantity?
A:There is no minimum order quantity, and one can also be done. The
only difference is the price and schedule.
3. Can you introduce your company?
A:I am very honored. I will send you the company’s introduction
document later to give you a more comprehensive and direct
introduction to our company’s information.
4. What are the advantages of your company?
A:Adequate inventory, and supply guarantee for the subsequent
renewal of supply, flexible provided according to different to
different needs of customers, providing different solutions.
5. Can i send samples?Report it to me along with the price?
A:You can send samples, the samples are subject to large pride, and
the freight needs to be borne by you.
6. How do your company deal with the problem on quality?
A:Our company has been doing this industry for almost 10 years. It
has already had a certain reputation. We will carefully analyze it.
If it is indeed our quality problem, you can rest assured that it
will do things according to the contract agreement and will never
let you have any after the worries, our service team will be happy
to serve you.
7 What about the quality ?
A:100% original with new package. we will test each item before
posted to make sure each item with good quality.
8 How many months for guarantee ?
A: 1 year quality guarantee
9 How to deal with any inferior -quality goods ?
A: Goods can be post by with our charge of post fee for any bad
quality products within guarantee time.
